John Deere

R200 Disc Mower

Manufacturer: John Deere
Model: R200 Disc Mower

Easy-to-attach 3-point hitch tractor hookup

High-clearance frame and suspension

Disc quill easy to remove for serviceability

Heavy-duty cutterbar for the toughest cutting conditions

Rotary disc cutterbar
Rotary disc cutterbar
#

A multi-V-belt drive system transfers power from the gearbox to each rotary disc.

Power is transmitted to the rotary discs through fully enclosed gears running in oil for a quiet, smooth, reliable operation.

 

All models have a spring-loaded belt tensioner for easier belt adjustment. The belt tension automatically compensates for initial belt stretch, increasing belt life.

High-speed rotary discs
High-speed rotary discs
#

Rotating at 2986 rpm, the high-speed discs cut in the toughest conditions.

The low-profile cutterbar allows a close cut while maintaining a level cutterbar. The cutting height is controlled by adjusting the tilt of the cutterbar.

Each disc has two free-swinging knives:

  • Easy to remove and replace
  • Two cutting edges, doubling the use life

Easy-to-attach 3-point hitch tractor hookup

Easy-to-attach 3-point hitch
Easy-to-attach 3-point hitch

The R160 and R200 Mowers attach to tractors with a Category 1 and 2, 3-point hitch. The R160 and R200 are not quick-hitch compatible.

 

The R160 and R200 models rely on the parking stand to hold up 3-point hitch arms to ensure easy hook up to the tractor.

Adjustable lower hitch pins
Adjustable lower hitch pins
#

Lower hitch pins can be adjusted left or right to match the mower offset for tractors with wider tire spacing. The R160 and R200 models have an offset range of 172 mm (7 in.).

Uptime

 Cutting arc provides a wide range of cutting angles

Easy-to-remove disc quill

Removable quill
Removable quill
#

The cutterbar is protected from severe impact should an object be struck.

  • Disc drive-shaft shears
  • Reduces chance of internal damage to cutterbar
  • Improves cutterbar reliability

Disc quills are easily removed from the top of the cutterbar for improved serviceability.

 

Each disc has two free-swinging knives:

  • Easy to remove and replace
  • Two cutting edges, doubling the use life
  • Swings away to reduce possible damage if a solid object is struck

Lift and suspension system

Heavy floatation spring
Heavy floatation spring

The disc mowers use the hydraulic cylinder to lift the cutterbar from the cutting position to the transport position, where the cutterbar automatically locks into place.

 

The R160 and R200 have a cutting arc of +35 degrees to -22 degrees.

 

A heavy spring establishes even flotation along the full length of the cutterbar in a variety of different field conditions and topography.

Performance

Cutting arc provides a wide range of cutting angles

 

Mower

PTO speed540 rpm
Minimum PTO HP26 kW
35 hp
Number of disksFive
Width of cut2 m
6.58 ft
Weight465 kg
1025 lb
Disk speed2986 rpm
Number of knives10
Lift systemHydraulic
Cutting arc+35 to -22 degree (angle)

Key Specs

MowerNumber of disks
Five
Number of knives
10
Width of cut
2 m
6.58 ft
Weight
465 kg
1,025 lb
Disk speed
2,986 rpm
Cutting arc
+35 to -22 degree (angle)
Lift system
Hydraulic
Minimum PTO HP
26 kW
35 hp
PTO speed
540 rpm
  • Cutting Width: 6ft. 7in. (2.0m)
  • Number of discs: 5
  • Weight: 940lb. (427kg)
  • Tractor Requirement: 35hp (25kW)
  • Disc Speed: 2,986rpm
  • PTO Speed: 540rpm
Chris Vonholten

I felt like I had been doing business with Martin Tractor for years even though it was my first interaction with them.

Contact This Location