John Deere

560M Round Baler

Manufacturer: John Deere
Model: 560M Round Baler
  • Available in the following models:
    • Standard (dry hay)
    • Silage
  • BaleTrak™ Pro monitor-controller
  • Exclusive DiamondTough™ triple weave belts

Vertical forming chamber maintains uniform bale density

Bale-starting diagram
Bale-starting diagram

As the hay enters the forming chamber from the pickup, belts immediately turn the hay to form a tight, dense core.

Incoming hay then feeds between the bale and the lower gate roll. Hay is tightly compressed into smooth, dense layers as it enters the bale.

Chaffing is greatly reduced to prevent loss and retain hay quality in the bale.

Full-sized bale in bale chamber
Full-sized bale in bale chamber

The idler arm rises with bale growth, forcing oil from the hydraulic cylinder through a pressure-relief valve to maintain uniform bale density throughout the bale-forming process.

MegaWide™ Plus pickup with MegaTough™ pickup teeth offers super capacity

460M MegaWide Plus pickup
460M MegaWide Plus pickup

A MegaWide Plus pickup is available on 450M, 550M, and 560M Round Balers. It is base equipment on the 450M Silage, 550M Silage, 460M, 460M Silage, and 560M Silage Balers. The MegaWide Plus pickup is also incorporated into the new MegaWide High Capacity and Cutting (HC2) high-capacity precutter feed system.

0 Series Balers have implemented specification levels for all models in the baler lineup, similar to what was done when the 459E was introduced. Pickup options will remain the same for the model’s equivalent specification. The precutter pickups will have the same MegaWide Plus pickups that will be offered in mid specification (M) or the premium specification (R) balers.

MegaWide Plus pickups make baling easier, especially in wide or windblown windrows, and increases productivity; more hay volume means more bales per hour.

  • Flare-to-flare width of 1.8 m (5.9 ft) on balers with a 1.2 m (4-ft) wide bale chamber
  • The MegaWide HC2 Precutter feed system on the 460M offers a 2.2 m (7.2-ft) wide flare-to-flare pickup width; 20 percent wider than our previous offerings on the 1.2-m (4-ft) wide balers.
  • MegaWide Plus pickup makes it easier to produce better-shaped bales and improves crop pickup in wide, windblown, or scattered windrows
  • Mega teeth, located at the ends of the pickup, pull crop around the flares when baling wide or windblown windrows
  • MegaTough pickup teeth provide greater strength and durability
  • Exclusive square design handles high-impact loads without yielding
  • Sturdy toothbar design
  • Self-adjusting roller baffle
  • Spiral rotor-feed system improves feeding in all crop conditions
  • Chain driven for positive feeding
  • Cut-out clutch protected
  • Semi-pneumatic gauge wheels
MegaTough pickup teeth
MegaTough pickup teeth

Mega and MegaTough pickup teeth are base equipment:

  • Mega teeth, at the ends of the pickup, are heavy-duty for long life and improved crop retrieval
  • MegaTough pickup teeth are designed to withstand the harshest baling conditions and provide long service life
Toothbars on 1.5-m (5-ft) baler
Toothbars on 1.5-m (5-ft) baler

The 1.2-m (4-ft) balers use a full-length, reinforced toothbar design.

The 1.5-m (5-ft) balers use a heavy, C-channel construction. The pickup toothbars are divided into two half-sections that mount to a center spider for increased strength and even crop feeding.

Roller baffle
Roller baffle

Available only on the MegaWide Plus pickup, the patented roller baffle is self-adjusting and produces smoother crop flow across the pickup. The roller also improves crop pickup in small windrows and prevents roll ahead of crop.

When combined with the MegaWide Plus pickup, this feeding system allows increased ground speed with less chance of plugging for increased productivity in all field conditions.

  • Self-adjusting
  • Smooths crop for even flow across pickup
  • Allows for faster ground speed with less chance of plugging
  • Increases operator productivity
Spiral rotor
Spiral rotor
Auger and rotor feed system
Auger and rotor feed system

The MegaWide Plus pickup uses a rotor-feeding assembly, which mounts behind the pickup for smooth and even crop flow into the bale chamber.

  • Augers and rotor teeth are driven on the same shaft, eliminating the need for additional drives.
  • The rotor is fixed to the baler frame, allowing positive and even feeding into the bale chamber.
  • Large-diameter converging augers have high crop-flow capacity, and auger scrolls help to force crop into the chamber.
  • Spiral design enhances feeding in uneven windrows and reduces loading on the rotor.
Rotor stripper
Rotor stripper

Rotor strippers allow crop to be lifted from the rotor teeth into the chamber without cutting or wrapping the crop.

Cut-out clutch protection and feeder-drive chain
Cut-out clutch protection and feeder-drive chain

The MegaWide Plus pickups and spiral rotor are chain-driven for positive bale starts with cutout clutch protection. The pickup is being driven off the drive roll and bypasses the starter roll. This will allow for reduced wear and breakage of the starter roll chain.

Semi-pneumatic gauge wheel
Semi-pneumatic gauge wheel

Semi-pneumatic gauge wheels provide smooth ground gauging over uneven terrain and protection to the pickup.

  • Stiffer rubber sidewalls
  • No air pressure to maintain, which mean no flat tires
  • Adjustable to meet pickup tooth-to-stubble height requirements

The pickup float springs are positioned for excellent flotation.

  • Adjustable to meet varying field conditions
  • Float springs only support the pickup reel
    • Rotor assembly is fixed to the baler frame, eliminating additional weight on the pickup system
Adjustable crank handle
Adjustable crank handle

The adjusting crank positions the pickup to the desired operating height to match crop or field conditions.

An optional hydraulic pickup lift cylinder is available as an attachment.

  • Makes raising for transport or clearing obstructions easy
  • Crank handle serves as a down stop
  • Adapts to regular, MegaTooth and MegaWide Plus pickups
  • Hydraulic pickup lift comes standard on premium machines

0 Series Round Balers - Model specification levels

Round baler models
Model Bale size Available pickups
450E 1.2 x 1.5 m
(4 x 5 ft)
Regular
450M 1.2 x 1.5 m
(4 x 5 ft)
Regular, MegaWide™ Plus
460M 1.2 x 1.8 m
(4 x 6 ft)
MegaWide Plus, MegaWide HC2
460R 1.2 x 1.8 m
(4 x 6 ft)
MegaWide Plus, MegaWide HC2
550M 1.5 x 1.5 m
(5 x 5 ft)
Regular, MegaWide Plus
560M 1.5 x 1.8 m
(5 x 6 ft)
Regular, MegaWide Plus
560R 1.5 x 1.8 m
(5 x 6 ft)
Regular, MegaWide Plus, MegaWide HC2
Round baler model specification
Baler option Applicable models
E = Economy

  • Dry hay only
450E
M = Standard

  • Dry hay
  • Silage
  • Precutter
450M, 460M,
550M*, and 560M
R = Premium

  • Dry hay
  • Precutter
460R and 560R

*NOTE: The 550M Round Baler will only be available in dry hay and silage configurations.

MegaWide™ High Capacity and Cutting (HC2) feeding system

0 Series Round Baler
0 Series Round Baler

The 0 Series Round Baler family welcomes the first, John Deere, North-American built precutter. This feed system in front of these machines is the MegaWide HC2. The MegaWide Plus name is known as the industry-leading feed system since its introduction with the 7 Series Balers. John Deere continues that legacy with the 0 Series. Proven designs of the MegaWide were maintained and improvements were made to key components to gain significant capacity.

Features of the MegaWide HC2

The MegaWide™ HC2 will only be available in a precutter configuration (available on the 450M, 460M, 460R, 560M, and 560R models):

  • 1.22-m (4-ft) wide machines will have 14 knives
  • 1.52-m (5-ft) wide machines will have 20 knives

The MegaWide HC2 has the same 2.2-m (7.22-ft) MegaWide Plus pickup from the 9 Series. Dry hay and silage 0 Series configurations will also have the MegaWide Plus pickup.

Baler driveline
Baler driveline
Greasing in one location
Greasing in one location

Before the introduction of the MegaWide HC2 , the cam-clutch protection for the driveline was only available on the 9 Series Premium Balers. It is in the base for the MegaWide HC2 precutter configurations. This driveline pushes the limitations of the baler and the MegaWide HC2 system by offering the best machine protection John Deere can provide.

Another feature brought over from the 9 Series Premium Balers and being offered on the 0 Series is the grease banks. All daily greasing can be done from the ground in one central location.

MegaWide HC<sup>2</sup> roller baffle and MegaWide Plus roller baffles”><br />
  <span class=MegaWide HC2 roller baffle and MegaWide Plus roller baffles

The roller baffle on the MegaWide HC2 doubled in size from the MegaWide Plus from 10.2-cm (4-in.) to 20.3-cm (8-in.) diameter to allow for increased speeds and performance in larger windrows.

560R Baler width
560R Baler width
450M Baler width
450M Baler width

The 450M, 460M, 460R, 560M, and 560R Balers that can be configured with the MegaWide HC2 feed system will have the same flare-to-flare pickup width of 2.2 m (7.21 ft). This 2.2-m (7.21-ft), flare-to-flare, width on 1.22-m (4-ft) balers is only a feature of the MegaWide HC2 feed system.

Primary rotor relationship to knives – front position
Primary rotor relationship to knives – front position
Primary rotor from bale chamber
Primary rotor from bale chamber

The primary rotor is only available on the MegaWide HCand is located directly behind the MegaWide pickups.

  • This rotor grabs the crop and drags it over the knives to size the crop to a theoretical length size of 66 mm (2.5 in.)
    • For the 1.22-m (4-ft) machines, there are 14 slots to receive the knives that are located on the floor of the feed system
    • The 1.52-m (5-ft) machine has 20 knives and 20 slots
Fast-pitch augers on the primary rotor
Fast-pitch augers on the primary rotor

Industry-exclusive, fast-pitch augers have been placed on the primary rotor to move dry hay and silage past the transition points to avoid plugging.

MegaWide HC<sup>2</sup> secondary rotor from bale chamber”><br />
  <span class=MegaWide HC2 secondary rotor from bale chamber

The secondary rotor is another component on the feed system that was re-designed from the MegaWide Plus feed system to handle the increased demands of the high-capacity system.

  • The secondary rotor in the MegaWide HC2 is similar in location and design as the MegaWide Plus spiral rotor.
  • The hex shaft on secondary rotor rotor on the MegaWide HC2 was increased from 3.2 cm (1.25 in.) from the MegaWide Plus to 3.8 cm (1.5 in.)
  • The diameter of the tube was increased for additional strength and to prevent silage wrapping
  • The number of tines was increased from two to three for additional capacity and flow of crop into the starter roll and chamber.
Third drive roll
Third drive roll

A third drive roll is another feature that will only be offered with the MegaWide HC2 feed system.

  • Precutting crop releases additional moisture into the feed system of the baler so the MegaWide HC2 feed system added a third drive roll on the number 11 roller to ensure trouble-free bale formation even in the most difficult, high-moisture silage conditions.
  • This feature is available only on the MegaWide HC2 feed system
External belt guides
External belt guides

All MegaWide HC2 feed systems will have silage components to limit maintenance and prevent crop build up on belts.

  • Driven auger
  • Starter roll scraper knife
  • Auxiliary take up roller
  • For precutter machines only – external belt guides
  • External belt guides were designed to dramatically reduce amount of chaff in the gate
  • Available through parts – retrofittable through 7 Series balers
Descriptive model numbering system

All 0 Series Balers use alpha-numeric identifiers for the model names:

  • The MegaWide HC2 can be ordered on mid specification (M) and premium specification (R) balers.

  • R specification balers will have the premium pickup with improved internal components that are covered under the 2-year/12,000-bale premium warranty

  • M specification balers and pickups will not contain premium baler components – exception for this is the MegaWide HC2 feed system will have the premium cam clutch for the driveline and grease banks.

For more information about the model specifications, see the chart below:

 

Baler option Applicable models
E = Economy

  • Dry hay only
450E
M = Standard

  • Dry hay
  • Silage
  • Precutter
450M, 460M,
550M*, and 560M
R = Premium

  • Dry hay
  • Precutter
460R and 560R

*NOTE: The 550M is only available in dry hay and silage configurations.

New Holland, Roll-Belt, and CropCutter are trademarks of CNH Global N.V. and its subsidiaries.

Increased torque – the MegaWide HC2 feed system required an additional drive configuration to power the primary rotor and to meet the capacity goals.

  • The MegaWide HC2 feed system has a T gearbox where the MegaWide Plus has a 90 degree box.
  • The MegaWide Plus system had a cut-out clutch that protected the spiral rotor and pickup.
  • The MegaWide HC2 eliminated that clutch because the secondary rotor is more robust than the MegaWide Plus spiral rotor.
    • This allowed the primary and secondary rotor to be driven directly from the driveline.
    • Both components are still clutch protected from the main driveline cam clutch, but there is approximately 10 times more torque being put through the primary and secondary rotor than what is found on the MegaWide Plus spiral rotor.
    • This exponential change in torque is the driving force of the capacity gains in the MegaWide HC2 feed system.
    • MegaWide HC2   pickup is still clutched for extended pickup life. That clutch is now located on the left-hand side of the baler. MegaWide Plus pickup clutches are still located on the right-hand side of the baler.

 MegaWide HC2 feed systems will not have the adjustable crank handle for the pickup.

  • MegaWide Plus machines will continue to have this an option.
Drop floor
Drop floor
Drop floor
Drop floor

Drop floor – if the baler exceeds capacity and plugs, the MegaWide HC2 can lower the knife floor from the cab of the tractor to easily feed the plug into the chamber.

  • Drop floor is an insurance policy to allow the operator to push the machine knowing that a plug can clear in 30 seconds, not 30 minutes.
  • In factory-observed testing with the 2016 test fleet, 99 percent of the plugs were cleared from the cab.
  • Floor is self-cleaning – when lowered to feed a plug, it allows chaff that has been built up around the knives to fall through into the windrow.
    • This release of crop allows the feed system to stay cleaner
    • Allows for easier engagement of the knives and servicing of the knives
  • The floor is also responsible for engaging the knives
    • Based on lack of success for re-engaging knives in competitive machines, John Deere made sure the MegaWide™ HC2 was built to meet the demands a Deere producer expects.
    • Knife-engagement forces on the MegaWide™ HC2 are 10 times that of the New Holland™ Roll-Belt™ 460 CropCutter® Baler. It gives the producer the confidence that if the knives are engaged, they are all up and cutting.
    • Once the knives are up, each knife has individual spring protection, limiting bent or broken knives.
    • Hit a rock and the knife moves out of the way and automatically re-engages.

Regular pickup offers large feed opening and low-profile, mid-mounted pickup

Regular pickup on 450E Baler with converging wheels
Regular pickup on 450E Baler with converging wheels

Mounted in front of the baler wheels and directly below the bale chamber, the pickup hugs the ground for clean crop retrieval. Hay movement is minimized.

  • V-belt driven
  • 450E and 450M Baler pickups are 116.6 cm (45.9 in.) wide
  • 550M and 560M Baler pickups are 156 cm (61.4 in.) wide
  • Large reel shaft and reel bearing

The small-diameter, low-profile pickup allows for good ground gauging and clean crop retrieval.

  • Handles large, heavy windrows of hay and high-moisture crops
  • Feeds hay directly to the forming chamber to reduce crop loss
  • Low-profile pickup minimizes hay lift to reduce chaffing and retain hay quality

Side flares prevent hay from blowing off the pickup ends, which reduces hay loss.

The closely-spaced pickup teeth extend to the baler side sheets to help build straight-edged bales.

Standard on regular pickups, compressor rods are contoured to control hay over the pickup radius for positive feeding. The compressor rack can be adjusted upward or downward to match the volume of material in the windrow and can be easily removed to match crop conditions.

Adjustable crank handle
Adjustable crank handle

The adjusting crank positions the pickup to the desired operating height to match crop or field conditions.

An optional hydraulic pickup lift cylinder is available as an attachment.

  • Makes raising for transport or clearing obstructions easy
  • Crank handle serves as a down stop
  • Adapts to regular and MegaWide™ Plus pickups
  • Hydraulic pickup lift comes standard on premium machines

NOTE: Crank is not an option for the MegaWide High Capacity and Cutting (HC2) feed system.

Adjustable hitch to match wide array of tractor drawbar heights

Side view of adjustable hitch
Side view of adjustable hitch
Front view of adjustable hitch
Front view of adjustable hitch

The 0 Series Round Balers came standard with an adjustable hitch and this feature will continue to be in base with the 0 Series Round Balers. This feature allows the hitch height to be adjusted to optimize crop-feeding performance. Due to the wide array of tractor tire sizes and drawbar heights, hitch adjustment may be necessary to get the proper feed opening of the baler. The adjustable hitch eliminates the need for the 51-mm (2-in.) thick tractor drawbar kit (AE57344) because it has a wider opening.

Benefits of the adjustable hitch:

  • Ability to match baler to numerous tire sizes
  • Allows for drawbar height to fall within 330 mm to 559 mm (13 in. to 22 in.) from the top of the drawbar to the ground
  • Eliminates narrow feed opening on the baler which can cause plugging
  • Allows pickup head to follow terrain without missing crop

All eight bolts must be used when adjusting the hitch. There are four different positions as shown below:

Position 1 (top) (factory setting) - regular pickups
Position 1 (top) (factory setting) – regular pickups
Position 2
Position 2
Position 3 (factory setting) - MegaWide Plus and MegaWide HC<sup>2</sup>“><br />
  <span class=Position 3 (factory setting) – MegaWide Plus and MegaWide HC2
Position 4 (bottom)
Position 4 (bottom)

Also standard on all 0 Series Round Balers, except the 450E, is the drawbar shield. This helps to eliminate hay from getting caught on the hitch of the baler. The drawbar shield is designed to allow the operator to remove or attach the flap without having to unhook the baler from the tractor.

Drawbar shield
Drawbar shield
Drawbar shield installed on baler
Drawbar shield installed on baler

Silage configuration

Staggered roller-auger kit
Staggered roller-auger kit
#

A silage-configuration baler allows the producer to put up silage hay. A silage configuration machine does not offer a precutter. There are three major components to a silage configuration baler: a staggered roller-auger kit (1), a starter roll-scraper knife, and a screen (2). The powered auger sits above the staggered roll on the baler to help keep wet hay from traveling up the belts and reduce buildup on the roll. The screen is bolted on the front of the baler as a safety feature. The knife/scraper is mounted in front of the starter roll to help prevent wrapping of wet crop on the starter roll.

The silage kit is offered as a bundle for field installation if the baler is not ordered as a silage-configuration machine from the factory. Attachment BE32442 is for 1.22-m (4-ft) wide machines and BE32443 is for1.52-m (5-ft) wide machines.

Also offered is a high-moisture kit. This kit does not include the same components that are on the silage-configuration balers. It offers the starter roll-scraper knife but does not include the staggered roll-auger kit. Attachment BE23828 is for 1.22-m (4-ft) machines and BE23829 is for 1.52-m (5-ft) machines.

Starter roll knife and screen
Starter roll knife and screen
#

Base equipment on: 450M Silage, 550M Silage, 460M Silage, 560M Silage, 450M Precutter, 460M/R Precutter and 560M/R Precutter.

Auxiliary take-up rolls
Auxiliary take-up rolls
#

Auxiliary take-up rolls prevent belt crossover and flipping in wet conditions. This roll is base equipment on all silage and precutter configuration balers. It also comes with the bale ramp bundle on the 440E and 450E Balers.

Precutter configuration
#
#

The 0 Series Round Baler family welcomes the first, John Deere, North-American built precutter. This feed system in front of these machines is the MegaWide HC2. The MegaWide Plus name is known as the industry-leading feed system since its introduction with the 7 Series Balers. John Deere continues that legacy with the 0 Series. Proven designs of the MegaWide were maintained and improvements were made to key components to gain significant capacity.

The MegaWide™ HC2 will only be available in a precutter configuration (available on the 450M, 460M, 460R, 560M, and 560R models):

  • 1.22-m (4-ft) wide machines will have 14 knives
  • 1.52-m (5-ft) wide machines will have 20 knives

The MegaWide HC2 has the same 2.2-m (7.22-ft) MegaWide Plus pickup from the 9 Series. Dry hay and silage 0 Series configurations will also have the MegaWide Plus pickup.

Automatic electric-tie option using BaleTrak™ Pro monitor allows for more productivity

Audible alarm
BaleTrak Pro monitor-controller
BaleTrak Pro monitor-controller

The BaleTrak Pro monitor-controller is included with the automatic electric twine tie option and the Edge-to-Edge net wrap option on the 450E Baler. The monitor sounds an alarm for near-full, full, and oversized bales.

  • Monitor beeps once to notify the operator to even-up the bale prior to reaching the desired size.
  • Monitor beeps twice when the bale reaches the desired size.
    • If the operator continues to feed hay into the baler, the monitor will sound continuously to warn of an oversized bale.
  • Bale shape bars are not available on the 450E Round Balers. The 450E Round Balers allow for adjustment of twine settings from the cab by using the BaleTrak Pro Monitor.
  • The number of wraps on the Edge-to-Edge net wrap option on the 450E can be set with the BaleTrak Pro.

The audible level of the monitor can be adjusted.

Exclusive DiamondTough™ belts with plate-type splices

Staggered belts
Staggered belts

John Deere’s 178-mm (7-in.) wide diamond-tread design ensures fast bale starts and grips the bale to prevent slippage and reduce chaffing. The treads are self-cleaning to reduce carryover. The belts are staggered to reduce the loss of fine material and are closely spaced to contain the hay for fast, easy starts.

The belts enclose 91 percent of the bale width to reduce loss of fine material and retain hay quality.

The staggered belt roll design enables any loose hay under or behind the belts to be returned to the pickup and into the baler. This design helps to prevent buildup at the front of the baler, which could cause hay loss and belt or splice damage.

DiamondTough triple-weave belts
DiamondTough triple-weave belts
#

Every baler in the 0 Series Family uses DiamondTough belts. Belts are constructed using a patented triple-weave process of nylon and polyester materials.

They have the strength to handle heavy shock loads and help maintain consistent belt length.

The DiamondTough belts are more puncture and tear resistant than other belts on the market and provide improved belt life and reliability.

Plate-type fasteners
Plate-type splices
Plate-type splices
#

All of the 0 Series Balers use the plate-type fasteners.

This closed-loop design uses a plate fastener with pre-assembled rivets that lock the fasteners into the belt, providing a powerful vice-type grip on the belt.

  • The plates and rivets are manufactured from high-tensile stainless steel.
  • Strong belt splices mean less maintenance and more productivity.
  • The loop area is cold forged, making it extremely wear resistant in the coupling area, resulting in a very long cycle life.
  • The spring steel pin is notched and locks into the splice connection without having to bend the pin or use external retainers.
Regular pickup - Stripper diameter: 25.4 cm
10 in.
Key Specs - Regular pickup - Number of teeth: 96
MegaWide Plus pickup - Width: Inside
196 cm
77 in.
Flare
221 cm
87 in.
Bale forming - Bale size indication: Electronic display on monitor
Baler - Weight: Shipping dry - 3,257 kg
7,182 lb
Shipping silage - 3,389 kg
7,472 lb
Shipping precutter - 4,239 kg
9,346 lb
MegaWide Plus pickup - Gauge wheels: Semi-pneumatic
MegaWide Plus pickup - Number of regular teeth: 120
Key Specs - High-capacity pickup - Number of mega teeth: Eight
Monitor - Auto wrap: Activates when bale reaches preset size
Baler - Height: Gate closed
279 cm
110 in.
Gate open
368 cm
145 in.
Monitor - Near full bale: Audible, adjustable alert
Monitor - Full bale: Audible, adjustable alert
Tire size - Standard: Dry and Precutter - High-flotation 14 L - 16.1, 8 PR
Silage - XL high-flotation 21.5L-16.1, 8 PR
Wrapping system - Control: Automatic to preset to bale size
Driveline - PTO lockback collar on tractor hookup: Yes
Monitor - Gate closed: Symbol on monitor
Monitor - Bale size: Mechanical and digital
Tractor Requirements - Minimum PTO: Dry Hay and Silage - 42 kW
55 hp
MegaWide HC kW
125 hp
Regular pickup - Lift control: Adjustable height control
Additional information - Date collected: 14-February-2018
High-capacity pickup - Number of middle teeth: 120
Driveline - Type: Constant-velocity (CV)
Driveline - Drive protection: Slip clutch
Key Specs - High-capacity pickup - Number of middle teeth: 120
Key Specs - Belts-other - width: 17.8 cm
7 in.
Key Specs - Regular pickup - Bars: Four
Monitor - Twine arm position Indicator: Mechanical
Tractor Requirements - Hydraulic SCV valves: One tractor selective control valve (SCV) is required when baler is equipped with electric twine wrap.
Two tractor SCVs are required when baler is equipped with hydraulic twine wrap.
Three tractor SCVs are required when baler is equipped with hydraulic twine wrap and a hydraulic pickup lift.
Wrapping system - Type: Standard
Electric
Driveline - PTO 60-degree free rotation: Yes
Key Specs - Bale size indication: Electronic display on monitor
Monitor - Oversize bale: Yes, audible and mechanical alerts
Bale forming - Belts-other: Number
Eight
Width
17.8 cm
7 in.
Texture
Diamond Tread friction surface belts
DiamondTough, triple-weave, single-ply belts
Wrapping system - Twine ball capacity: Eight
MegaWide Plus pickup - Number of mega teeth: Eight
Key Specs - Regular pickup - Tooth spacing: 6 cm
2.6 in.
High-capacity pickup - Gauge wheels: Semi-pneumatic
Baler - Width: With standard tires
226 cm
89 in.
With opt. tires (Hi-Flotation)
285 cm
112 in.
Regular pickup - Width: Inside
156 cm
62 in.
Flare
180 cm
71 in.
Bale - Size: Diameter
81 - 183 cm
32 - 72 in.
Width
157 cm
62 in.
1.5 x 1.8 m
5 x 6 ft
Key Specs - Density control: Hydraulic
Regular pickup - Gauge wheels: Semi-pneumatic
Wrapping system - Twine arms: Two
Bale - Weight: Full-size bale in dry crop
998 kg
2,200 lb
Max. allowable for silage bale
1,089 kg
2,500 lb
High-capacity pickup - Width: Inside
196 cm
77 in.
Flare
221 cm
87 in.
High-capacity pickup - Type: MegaWide High Capacity and Cutting (HC
Bale forming - Density control: Hydraulic
Regular pickup - Tooth spacing: 6 cm
2.6 in.
Key Specs - MegaWide Plus pickup - Number of mega teeth: Eight
Monitor - Bale forming: BaleTrak Pro
Regular pickup - Bars: Four
Baler - Length: Gate closed
371 cm
146 in.
Gate open
475 cm
187 in.
Tire size - Optional: With MegaWide Plus or MegaWide HC
Driveline - PTO speed: 540 or 1,000 rpm
Regular pickup - Number of teeth: 96
Key Specs - MegaWide Plus pickup - Number of regular teeth: 120
High-capacity pickup - Number of mega teeth: Eight
High-capacity pickup - Stripper diameter: 25.4 cm
10 in.
  • Diameter: 32-72 in. (81-183 cm)
  • PTO Speed: 560M, 560M Silage: 540/1000 560M MegaWide™ HC2: 1000
  • Height (Gate Closed): 110 in. (279 cm)
  • Width: 62 in. (157 cm)
  • Type: DiamondTough™ triple weave
  • PTO HP (Minimum): 560M, 560M Silage: 75 hp (56 kw) 560M MegaWide™ HC2: 125 hp (64 kw)
Chris Vonholten

I felt like I had been doing business with Martin Tractor for years even though it was my first interaction with them.

Contact This Location