HX14 HX14 Rotary Cutter

Manufacturer: John Deere
Model: HX14 HX14 Rotary Cutter
  • Larger, more durable gearboxes
  • Large-diameter, round-pan blade holders
  • Tractor hookup available
  • Max Flow cutting chamber for a clean cut

Warranty

Five-year limited gearbox warranty provided on every John Deere rotary cutter
Five-year warranty on all flex-wing gearboxes
Five-year warranty on all flex-wing gearboxes
Five-year warranty on all rotary cutter gearboxes
Five-year warranty on all rotary cutter gearboxes

John Deere is so confident in the reliability of the gearbox that rotary cutters come with a 5-year limited gearbox warranty.

 

There is also 1-year warranty on the complete machine, as well as drivelines and other components.

Tractor hookup available in two configurations

Lift type
Lift type (shown with iMatch™ hitch system)
Lift type (shown with iMatch™ hitch system)
#

The lift-type versions fit tractors with Category 2, 3, or 3N 3-point hitches (with or without Quick Hitch).

 

NOTE: The lift-type versions require a larger tractor than other versions. For HX10 Lift-Type Rotary Cutters, the minimum-size tractor recommended is a 6020 Series or equivalent. For HX14 Lift-Type Rotary Cutters, the minimum-size tractor recommended is a 7720 or equivalent. Refer to the tractor’s operator’s manual for ballasting instructions. The pull-type versions of the HX10 Multi-Spindle Rotary Cutter require a tractor with a minimum of 50 power take-off (PTO) hp. The HX14 pull-type versions require a tractor with a minimum of 60 PTO hp. Note that the type and volume of material being cut affect horsepower requirements.

Pull type
Pull type
Pull type
#

Parallel lift linkage helps keep the cutter level through all height adjustments. Cylinders are John Deere manufactured, meaning more reliability and durability.

Patented John Deere Double-Decker™ design for superior frame strength

Cross-section of exclusive Double-Decker design
Cross-section of exclusive Double-Decker design
#

The patented Double-Decker design improves strength and cutting performance while reducing top deck rust. Two welded decks include a 3-mm (11-gauge, 0.118-in.) to 3.5-mm (10-gauge, 0.138-in.) thick upper deck, depending on the model, and a 3-mm (11-gauge, 0.118-in.) to 4.5-mm (7-gauge, 0.177-in.) thick lower deck, depending on the model.

 

Internal stiffeners are sandwiched between the decks to add extra strength and rigidity.

 

The Double-Decker design also provides a sturdy base to support the gearcases. Gearcases need this sturdy base to resist the bending loads imposed upon them when blades contact immovable objects or the ground.

 

The bottom deck is the main defense against rocks and field debris, to help protect the top deck from impacts so it will retain its smooth form.

Larger, more durable gearcases

Gearcases are John Deere designed for reliability and dependability:

  • Center gearcase – 160 continuous hp or 200 peak hp
  • Outer gearcase – 100 continuous hp or 150 peak hp

Heavy-duty, tapered roller bearings and precision gears help ensure long life.

 

Output shafts are splined, not just keyed, for extra strength and durability.

Heavy-duty bowl support
Heavy-duty bowl support
#

Gearcases mount on heavy-duty bowl supports, which are continuously welded to the top and bottom decks. These bowls provide a lifelong base of support for the gearcase/blade holder mechanism.

 

The HX14 comes standard with five year warranty.

What is the best cutter for your job?

NOTE: Only for single spindle and multi-spindle.

 

John Deere rotary cutters lead the way with innovative design, superior performance, and proven durability. Valuable features such as the Double-Decker™ design and Max Flow cutting chamber prevent water and debris from accumulating on the smooth, dome-shaped top deck while the flat bottom deck absorbs the punishment from rocks and stumps.

 

The top deck stays smooth – no dents, no dings, no holes. The internal supports sandwiched between the top and bottom decks are key to the smooth and structure-free Max Flow cutting chamber, while at the same time provide added strength and durability.

 

To help promote safe operation, John Deere rotary cutters are equipped with front and rear safety-chain shields. John Deere rotary cutters continue to advance in value with powerful gearboxes, blade holders, and compatibility with a wide range of tractors.

 

Here are situations when a rotary cutter provides value:

  • Clipping pastures encourages grass growth, optimizing valuable pasture acreage.
  • Cutting grass and stalks helps control insects.
  • Routine cutting keeps weeds from reseeding.
  • It is the most cost efficient way to cut roadsides, parks, cemeteries, airport fields, hydro, gas, and telephone easements, and all other types of open properties.
  • Cutting grass waterways encourages root development and helps prevent erosion.
  • Knocking down stalks such as cotton, corn, or milo speeds up decomposition. This is essential in no-till and minimum-till fields.
  • Clearing out brush.
  • Control undergrowth and grass in orchards, vineyards, and groves.

Decide what model to use based on:

  • The size of the area to mow versus the size of the machine – the bigger the area to mow, the bigger the mower needs to be in order to be efficient during mowing hours. Similarly, the limitation of a small area will guide operators to use a smaller mower.
  • The amount of time and frequency it will be used – for longer hours and more frequency, choose a heavier duty machine.
  • Tractor compatibility – if there is a tractor the operator will be using, look for the tractor compatibility sheet to identify appropriate options.

John Deere rotary cutters are available in two duty-level categories:

  • Mid-duty
    • MX models are available in 1.5-m (5-ft), 1.8-m (6-ft), 2.1-m (7-ft), 2.5-m (8-ft), and 3.2-m (10-ft).
    • This duty-level category cuts brush up to 50.8 mm (2 in.) in diameter.
  • Heavy-duty
    • HX models are available in 3.2-m (10-ft) and 4.2-m (14-ft).
    • This duty-level category cuts brush up to 76.2 mm (3 in.) in diameter.
    • HX6 is available in 1.8-m (6-ft) and the HX7 is available in 2.1-m (7-ft) cut widths; they cut brush up to 101.6 mm (4 in.) in diameter.

NOTE: HX models are heavier built to cut at a 101.6 mm (4 in.) capacity level more frequently and for longer durations.

Gearcases and blade holders provide better performance

Gearcase and blade holder shown
Gearcase and blade holder shown

The John Deere gearboxes:

  1. Large seals
  2. Large housing
  3. Large output shaft
  4. Precision forged bevel gears
  5. Large bearings
  6. Stump jumper

Re-engineered gearcases and blade holders provide the following:

  • More horsepower
  • Faster blade-tip speed
  • Better performance
  • Quieter operation
  • Increased durability

Blades ensure clean cutting and fine shredding

Suction blades
Suction blade
Suction blade
#

Suction blades provide additional lift action for picking up downed material. The blades are 1.3 cm x 10.2 cm (0.5 in. x 4 in.) in size and heat-treated for long wear life.

 

A fast blade-tip speed (up to 16889 fpm) ensures clean cutting and fine shredding of material.

Flat blades
Flat blade
Flat blade
#

Flat blades are effective for any materials not downed and require suction for lifting.

 

Flat blades require less horsepower and have a cutting edge on both sides. Only available with double-blade system.

Dual blades (bar-type bladeholder only)
Dual blades
Dual blades
#

Dual blades are effective for increased shredding of crop residue.

 

The dual blades consist of a 1.3-cm x 10.2-cm (1/2-in. x 4-in.) lower suction blade and a 1.3-cm x 7.6-cm (1/2-in. x 3-in.) upper suction blade.

Capacity

Cutting capacity76.2 mm
3 in.
Cutting height50 to 305 mm
2 to 12 in.
Cutting width4,200 mm
165 in.
Cutting chamber Depth257 mm
10.5 in.

Dimensions

Deck typeDouble decker
Approx. weight1,390 kg
3,059 lb
Side skirt thickness6 (3) mm
0.25 (3) in.
Deck thicknessUpper
3.5 (10) mm
0.141 (10) in.
Lower
3.5 (10) mm
0.141 (10) in.
Overall width4,350 mm
171 in.
Transport width4,350 mm
171 in.
Deck shapeDomed
Overall length2,972 mm
117 in.

Tractor Compatibility

Tractor PTO1,000 rpm
Tractor PTO HP rangeMinimum PTO pull-type 45 kW
60 hp
Minimum PTO lift-type 67 kW
90 hp

Drivelines

ProtectionMain
Non-seize, slip-clutch driveline, pull-type has equal-angle Category 4 driveline
Connecting
Shock absorbing shafts
SizeMain
ASAE Category 5; lift-type
ASAE Category 4; pull-type
Connecting
ASAE Category 4 with Shear Bolt

Shielding

RearSolid
FrontChain

Blades

ThicknessSingle suction 13 mm
0.5 in.
Dual suction, upper 13 mm
Dual suction, lower 13 mm
Material flow systemMax flow
Blade tip speed
1000 RPM
4,540 m/min
14,896 fpm
272 km/h
169 mph
TypeSingle suction, dual suction
Overlap75 mm
2.95 in.
WidthSingle suction 102 mm
4 in.
Dual suction, upper 76.2 mm
3 in.
Dual suction, lower 102 mm
HolderType
Single suction; stump jumper
Dual suction; bar-type

Gearcases

HP ratingTransfer
Continuous 119 kW
160 hp
Peak 149 kW
200 hp
Outer
Continuous 75 kW
100 hp
Peak 112 kW
150 hp
Number3

Hitch

Category2, 3, 3N
TypeLift-Type, Pull-Type (Pull-Type has standard 10,000 lb; 4,536 kg, Safety Tow Chain)

Wheels

Row width adjustmentYes
TypeLaminated (Pull-type has severe-duty Ag tire option)
  • Hitch Category: Lift type: 2, 3 or 3N
  • Working Width: 13 ft. 9 in. (4.2 m)
  • PTO HP: Lift-type: 90 hp (67 kw)
    Pull-type: 60 hp (45 kW)